Description

Using technology derived from our flagship Installed Sound amplifier (Crown DriveCore Install series), the CDi DriveCore 2|1200 offers streamlined functionality to work in almost any large sized installation such as cinema, houses of worship, hotels, cruise lines, and more. Designed for ease-of-use in a variety of applications, the 2|1200 is a 2-channel amp that includes network control/monitoring, high-level DSP, front-panel interface, and support for driving up to 100Vrms speaker loads without requiring a transformer. The entire CDi DriveCore line comes pre-loaded with JBL speaker tunings to help make installations quicker and easier.

CDi 2|1200 Features

DriveCore™ Technology – Crown’s proprietary DriveCore technology eliminates hundreds of components within each amplifier, reducing the variability of component values, increasing reliability, resulting in incredible audio fidelity from an efficient design.
Network Control and Monitoring – Through HARMAN’s HiQnet Audio Architect software, the CDi DriveCore can be controlled, configured, and monitored through standard TCP/IQ network.
DSP – On-board Digital Signal Processor in each amplifier allows for custom configuration and includes these integrated features: • Input Router • Input Delay – Up to 1000ms • Input Parametric EQ – 8 band • Crossover • Output Parametric EQ – 8 band • Output Delay – Up to 100ms • LevelMAX™ Limiter
BLU link (BL models only) – Both receive and send channels over HARMAN’s 256 channel, fault-tolerant audio BUS, BLU link.
Direct Drive 70/100Vrms Output – Each output channel is capable of providing either 70V or 100V for high impedance applications.
Front-Panel Interface – Completely configure the amplifier using an intuitive front-panel interface.
GPIO/AUX Port – Recall presets, mute channels, monitor faults, power on/off the amplifier, and more through a combined GPIO/AUX Port.
Pre-loaded Speaker Tunings – For quicker and easier setup and installation.

Applications for the CDi 2|1200

Data Sheets, Manuals and Resources for the CDi 2|1200

Download the Crown_CDi_DriveCore_Series_CutSheet_06142017-(8)

Sensitivity (for full rated power at 8 ohms)	0.7V RMS (-0.8dBu, -3.0dBV)
Channels	2
Rated Power Output (per channel @ 4 ohms)	1200W
Voltage Gain (at maximum level setting) 4/8Ω, 70Vrms and 100Vrms Operation	34dB
Digital Signal Processing	96kHz, 32-bit floating point
Frequency Response (8Ω, 20 Hz - 20 kHz)	+/-0.25dB
BLU link Signal-to-Noise Ratio (ref. rated power, 100V, 20Hz - 20kHz)	>108dB
THD (full rated power, 20 Hz - 20 kHz)	0.35%
Analog Input Signal to Noise Ratio (ref. rated power, 100V, 20Hz - 20kHz) at 8 ohms)	> 104dB
Intermodulation Distortion (60Hz and 7kHz at 4:1, from - 30dB to full rated power)	≤0.35%
Damping Factor (20 Hz to 100 Hz)	> 1000
Crosstalk (below rated power) 20 Hz to 1 kHz	> 80dB
Common Mode Rejection (20Hz to 1kHz, typical)	>70dB
DC Output Offset (with inputs shorted)	±10mV
Input Impedance (nominally balanced, nominally unbalanced)	10 kΩ balanced, 5 kΩ unbalanced
Maximum Input Level (Low Amp Gain Mode)	+20dBU
Required AC Mains (±10%)	100V – 240V~ 50/60Hz
Cooling	Continuously variable speed forced air, front-to-back airflow
Power Supply Connector	15A IEC connector, 100 – 240V
Load Impedance Stereo/Dual Mode	2Ω - 16Ω; 70Vrms and 100Vrms
Load Impedance Bridge Mono	4Ω - 16Ω; 140Vrms and 200Vrms
Maximum Fan Noise (re dB SPL @ 1M)	54 dBA
Weight	17.2 lbs (7.8 kg)
Dimensions (inches) (W x H x D) (depth not including 1.3 inch front panel protrusion)	19 x 3.5 x 14.71

Crown Audio CDi 2|1200

Specifications of the CDi 2|1200

Description

CDi 2|1200 Features

Applications for the CDi 2|1200

Data Sheets, Manuals and Resources for the CDi 2|1200